The S235JRH pipe is manufactured following all ASTM, ASME, and other international standards. The EN 10219 S235JRH Pipe is composed of a chemical make-up of 0.17-0.20% carbon, 1.40% manganese, 0.009% of niobium, 0.040% of phosphorous and sulfur. These pipes have excellent corrosion resistance properties and can suffice in different temperatures. EN 10219 S235JRH Tube is referred to as structural hollow sections. These tubes can be formed by fine grain steel or non-alloy grades of steel. They are easy to maintain and are extremely durable. This S235JRH Hollow section is available in schedules of SCH 5 to SCH XXS and heavier. They possess good toughness, high-temperature resistance, and excellent abrasion resistance properties. The EN 10219 Welded hollow section can be welded with most traditional welding processes. They don’t require any pre-heating or suffer from post-weld carburization suffered in other grades. Cold Formed S235JRH Steel Welded Pipe possess a tensile strength between 316Mpa to 510Mpa and yield strength of minimum 235Mpa. These pipes can be easily elongated by 26%. The BS EN 10219 Structural hollow section is widely used in civil constructions, building bridges, structural frames, factory structures, and mechanical engineering systems. We are the leading supplier of the EN 10219 S235JRH pipes and tubes. We thrive to supply high-quality products at the most reasonable rates.
The S235JRH EN 10219 CHS Tube is used in structural and mechanical applications. They are stress relieved and possess good mechanical properties. These tubes offer a lighter, stronger, and have an aesthetic appeal to them. DIN 17120 S235JRH Circular Hollow Section has excellent dimensional tolerances. These tubes are available in nominal pipe sizes up to 3000NB and lengths up to 18000mm. The DIN 17120 EN 10219 Square Hollow Section can be formed by both cold and hot-rolling processes. The steel used in making them is completely killed and has excellent weldability. They protect against brittle facture taking place within the section. 1.0039 Steel Square Tube is used in earthling and the construction industry. These tubes possess a wall thickness between 0.5mm to 25mm and are available in lengths up to 14000mm. EN 10219-1 S235JRH Rectangular tube is designed with excellent properties of excellent resistivity and good conductivity. These low-cost pipes are durable and provide a long service life. The EN 10219-2 S235JRH RHS Tube is the most preferred tube in the industrial sector. These tubes are very flexible and come with sharp edges due to the fusion welding technology used in manufacturing them. EN 10219 Standard Rectangular Hollow Section is available in different sizes as per requirements. They come with an annealed, polished, or bright annealed finish. All our products including, the EN 10219 Steel Grade Square Hollow Pipe can be customized in different shapes and sizes as per our client’s requirements.
The Seamless EN 10210 Hollow Sections are produced without any welds or seams. They are extremely strong and have excellent resistance. These pipes can be easily cleaned and repair. Welded EN 10219 Hollow Sections are available in plain, beveled, threaded, and screwed tubing ends. Our renowned workers make use of cutting-edge technology and the best S235JRH Material to produce all the products in this grade. This is done following all international and national standards. If you have any queries or want to know more about our products or the EN 10219 S235JRH, contact us.
| Length | 6.0 m +/- 0.05 m Customized length ranging from 6 m to 11 m may be supplied. |
| Straightness | Minimum 1 : 200th of any length measured along the centre line (mill straightened condition) unless otherwise specifically arranged. |
| Twist tolerance | Maximum 2 mm ± 0.05 mm/m length-measured relative vertical shift of any adjacent corner of the section, measured by keeping one side on flat surface. |
| End Finish | Plain ended-Mechanically sheared, mill-cut finish without further machining. |
| Surface Finish / Chemical Properties | Black without any surface treatment of oiling or varnishing. |
| Raw Material | Sulphur content: 0.05% max, phosphorus content: 0.05% max, equivalent carbon percentage well within specified weldability limits with matching physical properties. For corrosion resistant steel in Cu-bearing variety, refer to the WRS section. |
| Weldability | Tata Structura Steel Hollow Sections are weldable with standard M.S. Electrodes without any pre-heating. |
| Packing | Bundled by sealing metal strap and each bundle is labelled for size, measurement, lot number etc. Approximate weight of each bundle is 1.5 Mt (+/-500 kg). |
| C | Si | Mn | P | S |
|---|---|---|---|---|
|
0.17 |
– |
1.4 |
0.035 |
0.035 |
| Yield strength | |
|---|---|
|
Material thickness |
Mpa |
|
≤ 16 |
235 |
|
≤ 16 ≤ 40 |
225 |
| Tensile strength | |
|---|---|
|
Material thickness |
Mpa |
|
< 3 |
360/510 |
|
≥ 3 ≤ 100 |
360/510 |
| Temperature | Thickness | Joules | |
|---|---|---|---|
|
JR |
20°C |
≤ 150 |
27 |
|
J0 |
0°C |
27 |
|
|
J2 |
-20°C |
27 |
|
| Outer Diameter (mm) | Wall Thickness (mm) | Kg/m | Length (m) | |
|---|---|---|---|---|
| 21.3 | x | 3.0 | 1.35 | 7.5 |
| 26.9 | x | 2.0 | 1.23 | 7.5 |
| 2.5 | 1.50 | |||
| 3.0 | 1.77 | |||
| 33.7 | x | 2.0 | 1.56 | 7.5 |
| 2.5 | 1.92 | |||
| 3.0 | 2.27 | |||
| 4.0 | 2.93 | |||
| 42.4 | x | 2.0 | 1.99 | 7.5 |
| 2.5 | 2.46 | |||
| 3.0 | 2.91 | |||
| 4.0 | 3.79 | |||
| 48.3 | x | 2.0 | 2.28 | 7.5 |
| 2.5 | 2.82 | |||
| 3.0 | 3.35 | |||
| 4.0 | 4.37 | |||
| 60.3 | x | 3.0 | 4.24 | 7.5 |
| 4.0 | 5.55 | |||
| 76.1 | x | 3.0 | 5.41 | 7.5 |
| 4.0 | 7.11 | |||
| 5.0 | 8.77 | |||
| 88.9 | x | 3.0 | 6.36 | 7.5 |
| 4.0 | 8.38 | |||
| 5.0 | 10.35 | |||
| 101.6 | x | 3.0 | 7.29 | 7.5 |
| 114.3 | x | 3.0 | 8.23 | 7.5 |
| 3.5 | 9.56 | |||
| 5.0 | 13.48 | |||
| 6.0 | 16.03 | |||
| 139.7 | x | 5.0 | 16.61 | 7.5 |
| 168.3 | x | 5.0 | 20.14 | 7.5 |
| Outside diameter (Od) mm | Wall thickness (Wt) mm | ||||||
|---|---|---|---|---|---|---|---|
| Tolerance band | Tol ± | Tolerance band | Tol ± | ||||
| 21.3 | – | 50 | 0.5 mm | 2 | – | 5 | 10% |
| 50 | – | 168.3 | 1.0% | 5 | – | 12 | 0.5 mm |
| HxB (mm) | Wt (mm) | Kg/m | Er | L (m) | |
|---|---|---|---|---|---|
| 20 x 20 | x | 2.0 | 1.12 | 4.0 | 7.5 |
| 25 x 25 | x | 2.0 | 1.43 | 4.0 | 7.5 |
| 2.5 | 1.75 | 5.0 | |||
| 3.0 | 2.05 | 6.0 | |||
| 30 x 30 | x | 2.0 | 1.74 | 4.0 | 7.5 |
| 2.5 | 2.14 | 5.0 | |||
| 3.0 | 2.52 | 6.0 | |||
| 40 x 40 | x | 2.0 | 2.37 | 4.0 | 7.5 |
| 2.5 | 2.92 | 5.0 | |||
| 3.0 | 3.46 | 6.0 | |||
| 4.0 | 4.48 | 8.0 | |||
| 50 x 50 | x | 2.0 | 2.99 | 4.0 | 7.5 |
| 2.5 | 3.70 | 5.0 | |||
| 3.0 | 4.39 | 6.0 | |||
| 4.0 | 5.73 | 8.0 | |||
| 5.0 | 7.01 | 10.0 | |||
| 60 x 60 | x | 3.0 | 5.32 | 6.0 | 7.5 |
| 4.0 | 6.97 | 8.0 | |||
| 5.0 | 8.56 | 10.0 | |||
| 6.0 | 10.09 | 12.0 | 6.0 | ||
| 70 x 70 | x | 3.0 | 6.26 | 6.0 | 7.5 |
| 3.5 | 7.25 | 7.0 | |||
| 5.0 | 10.12 | 10.0 | |||
| 75 x 75 | x | 3.0 | 6.73 | 6.0 | 7.5 |
| 80 x 80 | x | 3.0 | 7.19 | 6.0 | 7.5 |
| 3.5 | 8.34 | 7.0 | |||
| 4.0 | 9.46 | 8.0 | |||
| 5.0 | 11.68 | 10.0 | |||
| 6.0 | 13.82 | 12.0 | |||
| 8.0* | 17.93 | 20.0 | 12.0 | ||
| 90 x 90 | x | 3.5 | 9.43 | 7.0 | 7.5 |
| 5.0 | 13.23 | 10.0 | |||
| 6.0* | 15.69 | 15.0 | 12.0 | ||
| 100 x 100 | x | 3.0 | 9.06 | 6.0 | 7.5 |
| 4.0 | 11.96 | 8.0 | |||
| 5.0 | 14.79 | 10.0 | |||
| 6.0 | 17.56 | 12.0 | |||
| 8.0* | 22.92 | 20.0 | 12.0 | ||
| 10.0* | 27.90 | 30.0 | |||
| 120 x 120 | x | 5.0 | 17.90 | 10.0 | 7.5 |
| 150 x 150 | x | 5.0 | 22.57 | 10.0 | 7.5 |
| 6.0 | 26.90 | 12.0 |
| External dimensions (H x B) mm | Wall thickness (Wt) mm | ||||||
|---|---|---|---|---|---|---|---|
| Tolerance band | Tol ± | Tolerance band | Tol ± | ||||
| 20 | – | 50 | 0.5 mm | 2 | – | 5 | 10% |
| 50 | – | 100 | 1.0% | 5 | – | 12 | 0.5 mm |
| 100 | – | 200 | 0.8% | ||||
| 200 | – | 400 | 0.6% | ||||
| HxB (mm) | Wt (mm) | Kg/m | Er | L(m) | |
|---|---|---|---|---|---|
| 40 x 20 | x | 2.0 | 1.74 | 4.0 | 7.5 |
| 50 x 25 | x | 2.0 | 2.21 | 4.0 | 7.5 |
| 2.5 | 2.72 | 5.0 | |||
| 3.0 | 3.22 | 6.0 | |||
| 50 x 30 | x | 2.5 | 2.92 | 5.0 | 7.5 |
| 3.0 | 3.46 | 6.0 | |||
| 60 x 40 | x | 2.5 | 3.70 | 5.0 | 7.5 |
| 3.0 | 4.39 | 6.0 | |||
| 4.0 | 5.73 | 8.0 | |||
| 5.0 | 7.01 | 10.0 | |||
| 75 x 50 | x | 3.0 | 5.56 | 6.0 | 7.5 |
| 80 x 40 | x | 2.0 | 3.61 | 4.0 | 7.5 |
| 2.5 | 4.48 | 5.0 | |||
| 3.0 | 5.32 | 6.0 | |||
| 4.0 | 6.97 | 8.0 | |||
| 5.0 | 8.56 | 10.0 | |||
| 90 x 50 | x | 3.5 | 7.25 | 7.0 | 7.5 |
| 5.0 | 10.12 | 10.0 | |||
| 100 x 50 | x | 2.5 | 5.64 | 5.0 | 7.5 |
| 3.0 | 6.73 | 6.0 | |||
| 4.0 | 8.84 | 8.0 | |||
| 5.0 | 10.90 | 10.0 | |||
| 6.0 | 12.89 | 12.0 | |||
| 100 x 60 | x | 3.5 | 8.34 | 7.0 | 7.5 |
| 120 x 60 | x | 3.5 | 9.43 | 7.0 | 7.5 |
| 5.0 | 13.23 | 10.0 | |||
| 120 x 80 | x | 5.0 | 14.79 | 10.0 | 7.5 |
| 150 x 100 | x | 5.0 | 18.68 | 10.0 | 7.5 |
| 6.0 | 22.23 | 12.0 | |||
| 160 x 80 | x | 5.0 | 17.90 | 10.0 | 7.5 |
| 200 x 100 | x | 5.0 | 22.57 | 10.0 | 7.5 |
| External dimensions (H x B) mm | Wall thickness (Wt) mm | ||||||
|---|---|---|---|---|---|---|---|
| Tolerance band | Tol ± | Tolerance band | Tol ± | ||||
| 20 | – | 50 | 0.5 mm | 2 | – | 5 | 10% |
| 50 | – | 100 | 1.0% | 5 | – | 12 | 0.5 |
| 100 | – | 200 | 0.8% | ||||
| 200 | – | 400 | 0.6% | ||||
