If you are looking for a product to connect 2 pipes or tubes then a variety of flanges are available in the market. One such flange is the Hastelloy C276 Flanges. It is used to measure the flow rate of liquids or gases in a particular pipe. Therefore eliminating the need for drilling a bore into the pipe to check the flow rate. These Hastelloy Flanges have a higher melting point of 1370 degrees C. This allows the flange to operate at a higher operating temperature. Wnr 2.4819 Weld Neck Flangeis used to stop one end of the pipe or valve opening. Forging these flanges makes them strong.
Hastelloy Flanges manufacturers recommend these as they remain in shape due to the fact that they are made up of a single piece of metal. The different sizes of these flanges range from ½ inch to 60 inches. Hastelloy C276 Flanges are widely used in sour gas applications. The waste produced by these industries is toxic and requires Nickel Alloy C276 Slip On Flange to absorb the toxicity. Oxyacetylene and submerged arc method is not recommended for fabrication of ASTM B564 UNS N10276 Flange that is meant to be used in corrosion service. They are said to harden easily when compared to other austenitic stainless steel.
ASME SB 564 N10276 Blrf Flange may require intermittent annealing with several cold work stages. Whereas, hot forming of these flanges should be performed between 1600 degrees F to 2250 degrees F. Hastelloy C276 Lap Joint Flange is widely used in marine engineering, waste treatment, and pollution control. The Uns N10276 Blind Flanges are usually rapidly quenched after solution heat treatment. They are widely used to close or terminate pipes. Hastelloy Blind Flangeis the best option for industries that use corrosive chemicals on a daily basis.Hastelloy Flange Ratingdiffers as per the class that it belongs to.
Specification: ASTM B564/ ASME SB564, ASTM B366/ ASME SB366
Grade: Hastelloy C276 (UNS N10276, Alloy C276, 2.4819), Hastelloy C22 (UNS N06022, Alloy C22, 2.4602), Hastelloy B2 (UNS N10665, Alloy B2, 2.4617), Hastelloy X (UNS N06002, Alloy X)
Connect Type/ Flange Face Type: Raised Face (RF), Flat Face (FF), Ring Type Joint (RTJ), Lap-Joint Face (LJF), Large Male-Female (LMF), Small Male-Female (SMF), Large Tongue & Groove, Small Tongue, Groove
Size Range: 1/2" (15 NB) to 48" (1200NB) DN10~DN5000
Facings: Raised Face, RTJ etc.
To ANSI, DIN, EN, JIS, etc. or according to drawing
ASTM B564 UNS N10276 Welding Neck Flanges/ WNRF
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Plate Flanges
AS A150, AS A300, TABLE D,E,F,H, DIN, ND-6,10, 16, 25, 40
ASTM B564 UNS N10276 Slip On Flanges/ SORF
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Blind Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Threaded Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Socket Weld Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Orifice Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Blank Flange
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
Blank Flange Rotatable Hastelloy C276
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Welding Flange Rotatable
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Flange with Tube
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Reducing Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 CF (ConFlat) Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Flange Bolted Weld-On
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Square /Exhuast Flange
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Lap Joint Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Girth Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Spectacle Blind Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Anchor Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Screw Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Ring Joint Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Swivel Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 ANSI 150 Flanges
Flat Face, Raised Face, Tongue, Groove, Female, Male, RJ Face
ASTM B564 UNS N10276 Long WN Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Spade Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Spacer Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
ASTM B564 UNS N10276 Figure 8 Flanges
Class :150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
We are Manufacturer| Suppliers | Distributor| Stockholder| Wholesaler| Dealer| Stockist| Exporter| Importer of Hastelloy Alloy C276 Slip-On Flanges in Mumbai, India
The Socket Weld Flange is similar to a ASTM B564 UNS N10276 Hastelloy C276 Flanges except it has a bore and a counter bore dimension. The counter bore is slightly lager than the outer diameter of the matching pipe, allowing the pipe to be inserted into the flange similar to a B564 UNS N10276 slip-on flange. Buy ASTM B564 UNS N10276, Alloy C276 Slip-On Flanges, Hastelloy C276 SORF Flange, ASME SB 564 Slip-On Flanges, B564 UNS N10276 at Best Price in India.
ASTM B564 UNS N10276 Slip-On Flanges Standard
We are Manufacturer| Suppliers | Distributor| Stockholder| Wholesaler| Dealer| Stockist| Exporter| Importer of Hastelloy Alloy C276 Threaded Flanges in Mumbai, India
The B564 UNS N10276 Threaded Flange is similar to the slip-on flange, but the bore is threaded. Its chief merit is that it can be assembled without welding, explaining its use in low pressure services at ordinary atmospheric temperatures and in highly explosive areas where welding create a hazard. Buy ASTM B564 UNS N10276, Alloy C276 Threaded Flanges, Hastelloy C276 Screwed Flange, ASME SB 564 Threaded Flanges, B564 UNS N10276 at Best Price in India.
We are Manufacturer| Suppliers | Distributor| Stockholder| Wholesaler| Dealer| Stockist| Exporter| Importer of Hastelloy Alloy C276 Weld Neck Flanges in Mumbai, India
The B564 UNS N10276 Weld Neck Flange is normally referred to as the "high hub" flange. It is designed to transfer stresses to the pipe, thereby reducing high stress concentrations at the base of the flange. Buy ASTM B564 UNS N10276, Alloy C276 Weld Neck Flanges, Hastelloy C276 WNRF Flange, ASME SB 564 Weld Neck Flanges, B564 UNS N10276 at Best Price in India.
We are Manufacturer| Suppliers | Distributor| Stockholder| Wholesaler| Dealer| Stockist| Exporter| Importer of Hastelloy Alloy C276 Socket Weld Flanges in Mumbai, India
B564 UNS N10276 Socket Weld Flange is a solid disk used to block off a pipeline or to create a stop. The Socket Weld flange is machined in the same manner as a regular flange with the mounting holes around the perimeter and the gasket sealing rings machined into the mating surface. Buy ASTM B564 UNS N10276, Alloy C276 Socket Weld Flanges, Hastelloy C276 SWRF Flange, ASME SB 564 Socket Weld Flanges, B564 UNS N10276 at Best Price in India.
We are Manufacturer| Suppliers | Distributor| Stockholder| Wholesaler| Dealer| Stockist| Exporter| Importer of Hastelloy Alloy C276 Blind Flanges in Mumbai, India
The B564 UNS N10276 Blind Flange is a solid disk used to block off a pipeline or to create a stop. The UNS N10276 blind flange is machined in the same manner as a regular flange with the mounting holes around the perimeter and the gasket sealing rings machined into the mating surface. Buy ASTM B564 UNS N10276, Alloy C276 Blind Flanges, Hastelloy C276 BLRF Flange, ASME SB 564 Blind Flanges, B564 UNS N10276 at Best Price in India.
We are Manufacturer| Suppliers | Distributor| Stockholder| Wholesaler| Dealer| Stockist| Exporter| Importer of Hastelloy Alloy C276 Reducing Flanges in Mumbai, India
We supply reducing flanges (WN, SW, SO, Thrd) with the hubs or made from blinds (in the cases of SO or Thrd). Buy ASTM B564 UNS N10276, Alloy C276 Reducing Flanges, Hastelloy C276 reducing flanges with hubs, ASME SB 564 Reducing Flanges, B564 UNS N10276 at Best Price in India.
We are Manufacturer| Suppliers | Distributor| Stockholder| Wholesaler| Dealer| Stockist| Exporter| Importer of Hastelloy Alloy C276 Lap Joint Flanges in Mumbai, India
The B564 UNS N10276 Lap Joint Flange is practically identical to a slip-on flange except it has a radius at the intersection of the bore and flange race. This radius is necessary to have the flange accommodate a lap joint stub end. Normally, a lap joint flange and a lap joint stub end are mated together in an assembly system. Buy ASTM B564 UNS N10276, Alloy C276 Lap Joint Flanges, Hastelloy C276 LJ Flange, ASME SB 564 Lap Joint Flanges, B564 UNS N10276 at Best Price in India.
We are Manufacturer| Suppliers | Distributor| Stockholder| Wholesaler| Dealer| Stockist| Exporter| Importer of Hastelloy Alloy C276 Plate Flanges in Mumbai, India
We are specialised manufacturer & exporter of high quality ASME/ANSI/DIN standard B564 UNS N10276 plate flanges in India. Buy ASTM B564 UNS N10276, Alloy C276 Plate Flanges, Hastelloy C276 Flat Flange, ASME SB 564 Plate Flanges, B564 UNS N10276 at Best Price in India.
We are Manufacturer| Suppliers | Distributor| Stockholder| Wholesaler| Dealer| Stockist| Exporter| Importer of Hastelloy Alloy C276 Orifice Flanges in Mumbai, India
B564 UNS N10276 Orifice Flanges are used with orifice meters for the purpose of measuring the flow rate of either liquids or gases in the respective pipeline. Buy ASTM B564 UNS N10276, Alloy C276 Orifice Flanges, Hastelloy C276 Orifice Plate Flange, ASME SB 564 Orifice Flanges, B564 UNS N10276 at Best Price in India.
| American Series | European Series |
|---|---|
| Flat Face (FF) | Type A (Flat Face) |
| Raised Face (RF) | Type B (Raised Face) |
| Tongue (T) | Type C(Tongue) |
| Groove (G) | Type D (Groove) |
| Female (F) | Type E (Spigot) |
| Male (M) | Type F (Recess) |
| Ring Joints Face (RJ) | Type G (O-Ring Spigot) |
| - | Type H (O-Ring Groove) |
| ASME B16.5-2013 | ASME B16.47-2011 | MSS SP-44-2010 |
| EN 1092-1-2007 | EN 1759-1-2004 | ISO 7005-1-1992 |
| GB/T 9112-2010 | GB/T 9123-2010 | AS 2129-2000 |
| HG/T 20592-2009 | HG/T 20615-2009 | HG/T 20623-2009 |
| SH/T 3406-2013 | GOST- AFNOR- BS- DIN | - |
| STANDARD | HASTALLOY C276 |
|---|---|
| UNS | N10276 |
| WERKSTOFF NR. | 2.4819 |
| EN | NiMo16Cr15W |
| BS | – |
| GOST | ХН65МВУ |
| OR | ЭП760 |
| JIS | NW 0276 |
| DENSITY (G/CM 3) | 8.89 |
| DENSITY (LB/IN 3) | 0.321 |
| MELTING POINT (°C) | 1325 – 1370 |
| MELTING POINT (°F) | 2415 – 2500 |
| ELEMENT | HASTELLOY C 276 |
|---|---|
| NI | 50.99 min* |
| CR | 14.50 – 16.50 |
| MO | 15.00 – 17.00 |
| FE | 4.00 – 7.00 |
| W | 3.00 – 4.50 |
| C | 0.010 max |
| SI | 0.08 max |
| CO | 2.50 max |
| MN | 1.00 max |
| V | 0.35 max |
| P | 0.04 max |
| S | 0.03 max |
| CONDITION | TENSILE STRENGTH | YEILD STRENGTH | ELOGNATION |
|---|---|---|---|
| ANNEALED | 100 (690) | 41 (283) | 40 |
| Marking | Product and Designation | |||||
|---|---|---|---|---|---|---|
| Corrosion Resistant Fittings | ASME Pressure Fittings | Alloy | UNS Designation | Pipe or Tube | Plate, Sheet, strip | Bar Forging, and Forging Stock |
CR HC 276 |
WP HC 276 |
Low C-Ni-Mo-Cr |
N10276 |
B619, B622, B626 |
B575 |
B574, B564,B462, B472 |
